Start converting c code to rust

rust/src/main.rs

@@ -1,8 +1,12 @@
 #![no_std]
 #![no_main]
+#![feature(abi_avr_interrupt)]
+
+mod setup;
 
 use arduino_hal::{delay_ms, pins, Peripherals};
 use core::panic::PanicInfo;
+use setup::Setup;
 
 #[panic_handler]
 fn panic(_info: &PanicInfo) -> ! {
@@ -27,5 +31,15 @@ fn panic(_info: &PanicInfo) -> ! {
 
 #[arduino_hal::entry]
 fn main() -> ! {
-    loop {}
+    let setup = Setup::default();
+
+    loop {
+        fuzz(&setup);
     }
+}
+
+fn fuzz(setup: &Setup<'_>) {}
+
+#[avr_device::interrupt(atmega328p)]
+#[allow(non_snake_case)]
+fn TIMER1_COMPA() {}

rust/src/setup.rs

@@ -0,0 +1,113 @@
+use core::mem;
+
+use arduino_hal::{
+    hal::{
+        adc,
+        port::{PB4, PB5, PC4, PC5, PD2},
+    },
+    pac::{
+        adc::adc::ADC_SPEC,
+        tc1::{ocr1a::OCR1A_SPEC, ocr1b::OCR1B_SPEC},
+    },
+    pins,
+    port::{
+        mode::{Input, Output, PullUp},
+        Pin,
+    },
+    Peripherals,
+};
+use avr_device::generic::Reg;
+
+pub struct Setup<'a> {
+    pub led: Pin<Output, PB5>,
+    pub footswitch: Pin<Input<PullUp>, PB4>,
+    pub toggle: Pin<Input<PullUp>, PD2>,
+    pub push_button_1: Pin<Input<PullUp>, PC5>,
+    pub push_button_2: Pin<Input<PullUp>, PC4>,
+
+    ocr1a: &'a Reg<OCR1A_SPEC>,
+    ocr1b: &'a Reg<OCR1B_SPEC>,
+
+    adc: &'a Reg<ADC_SPEC>,
+}
+
+impl<'a> Setup<'a> {
+    //defining the output PWM parameters
+    // pwm frequency - 31.3KHz
+    const PWM_FREQ: u16 = 0x00FF;
+    // Fast (1) or Phase Correct (0)
+    const PWM_MODE: u8 = 0;
+    // 2 PWMs in parallel
+    const PWM_QTY: u8 = 2;
+
+    pub fn write_output(&self, output: u16) {
+        let high_byte = ((output + 0x8000) >> 8) & 0x00FF;
+        let low_byte = output & 0x00FF;
+
+        self.ocr1a.write(|w| unsafe { w.bits(high_byte) });
+        self.ocr1b.write(|w| unsafe { w.bits(low_byte) });
+    }
+
+    pub fn get_input(&self) -> u16 {
+        self.adc.read().bits()
+    }
+}
+
+impl<'a> Default for Setup<'a> {
+    fn default() -> Self {
+        let dp = Peripherals::take().unwrap();
+
+        // turn on outputs
+        dp.PORTB.ddrb.write(|w| unsafe { w.bits(0x02) });
+
+        let pins = pins!(dp);
+
+        // defining harware resources
+        let led = pins.d13.into_output();
+        let footswitch = pins.d12.into_pull_up_input();
+        let toggle = pins.d2.into_pull_up_input();
+        let push_button_1 = pins.a5.into_pull_up_input();
+        let push_button_2 = pins.a4.into_pull_up_input();
+
+        // setup ADC
+        // left adjust, adc0, internal vcc
+        dp.ADC.admux.write(|w| unsafe { w.bits(0x60) });
+        // turn on adc, ck/32, auto trigger
+        dp.ADC.adcsra.write(|w| unsafe { w.bits(0xe5) });
+        // t1 capture for trigger
+        dp.ADC.adcsrb.write(|w| unsafe { w.bits(0x07) });
+        // turn off digital inputs for adc0
+        dp.ADC.didr0.write(|w| unsafe { w.bits(0x01) });
+
+        // setup PWM
+        dp.TC1.tccr1a.write(|w| unsafe {
+            w.bits(((Self::PWM_QTY - 1) << 5) | 0x80 | (Self::PWM_MODE << 1))
+        });
+        // ck/1
+        dp.TC1
+            .tccr1b
+            .write(|w| unsafe { w.bits((Self::PWM_MODE << 3) | 0x11) });
+        // interrupt on capture interrupt
+        dp.TC1.timsk1.write(|w| unsafe { w.bits(0x20) });
+        dp.TC1.icr1.write(|w| unsafe { w.bits(Self::PWM_FREQ) });
+
+        let ocr1a = &dp.TC1.ocr1a;
+        let ocr1b = &dp.TC1.ocr1b;
+        let adc = &dp.ADC.adc;
+
+        unsafe { avr_device::interrupt::enable() };
+
+        Self {
+            led,
+            footswitch,
+            toggle,
+            push_button_1,
+            push_button_2,
+
+            ocr1a: unsafe { mem::transmute(ocr1a as *const _) },
+            ocr1b: unsafe { mem::transmute(ocr1b as *const _) },
+
+            adc: unsafe { mem::transmute(adc as *const _) },
+        }
+    }
+}